Basler-electric DECS-250N User Manual Page 68
- Page / 370
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
52 9440500990 Rev D
Protection DECS-250N
Figure 38. Exciter Diode Monitor Protection Settings
A
EDM Pole Ratio: Adjustable from 0 to 10 in 0.01 increments.
B
Open Diode Pickup Level (%): Adjustable from 0 to 100% in 0.1% increments.
C
Shorted Diode Pickup Level (%): Adjustable from 0 to 100% in 0.1% increments.
D
Open Diode Delay (s): Adjustable from 10 to 60 seconds in 0.1 second increments.
E
Shorted Diode Delay (s): Adjustable from 5 to 30 seconds in 0.1 second increments.
F
Disable Level (%): Adjustable from 0 to 100% in 0.1% increments.
G
Mode: Select Disabled or Enabled.
Setting the Pickup Level—Number of Generator Poles Unknown
The DECS-250N can detect shorted diode conditions when the number of generator poles is not known.
To provide this protection, disable open diode protection, set the pole ratio at zero, and enable shorted
diode protection. Multiply the maximum EDM ripple level, obtained under Finding the Maximum Field
Ripple Current, by 30. The multiplier can be varied between 20 and 40 to increase or decrease the pickup
margin. However, reducing the multiplier could result in nuisance shorted diode indications.
Testing the EDM Settings
Start the generator from rest and increase the speed and voltage to the rated value. Load the machine to
its rating and confirm that no failed diode annunciations occur. All of the EDM setup guidelines presented
here assume that the exciter diodes were not opened or shorted at the time of setup and testing.
Power Input Failure
A power input failure condition exists when any one of the following occurs:
1-Phase Operating Power
• When operating power decreases below 50 Vac, a power input failure condition exists.
3-Phase Operating Power
• All three phases of operating power decrease below 50 Vac
• One or more phases of operating power decreases below 10 Vac
• A phase-to-phase voltage imbalance greater than 20% exists at the operating power input
The DECS-250N settings must be properly set to match the active operating power configuration. For
example, if the DECS-250N settings reflect a 3-phase power configuration but the actual operating power
configuration is 1-phase then the DECS-250N will interpret the one phase as an imbalance and set an
alarm/trip. For more information on 1- and 3-phase operating power settings see Configuration and
Specifications.
Power input failure protection can be used for PMG applications, shunt-, or PMG-powered systems. This
protection is only active in Start mode and after soft start. A time delay setting
A
delays power input failure
annunciations to accommodate transient reductions/imbalances in the operating power input voltage.
Power input failure protection can be enabled and disabled
B
without altering the time delay setting. The
- INSTRUCTION MANUAL 1
- Preface 3
- Warning! 4
- 9440500990 Rev D iii 5
- DECS-250N Preface 5
- Contents 7
- Introduction 17
- Applications 18
- Package 18
- Storage 19
- 4 9440500990 Rev C 20
- Introduction DECS-250N 20
- Controls and Indicators 21
- Menu Navigation 22
- Adjusting Settings 23
- Display Setup 23
- 8 9440500990 Rev D 24
- Screen Scrolling 24
- Power Inputs 25
- 10 9440500990 Rev D 26
- Power Inputs DECS-250N 26
- Power Stage 27
- 12 9440500990 Rev D 28
- Power Stage DECS-250N 28
- Voltage and Current Sensing 29
- 14 9440500990 Rev D 30
- Cross-Current Compensation 30
- Bus Voltage 31
- 16 9440500990 Rev D 32
- Synchronizer 33
- 18 9440500990 Rev D 34
- Synchronizer DECS-250N 34
- Angle Compensation 34
- Failure of Synchronization 34
- 22 9440500990 Rev D 38
- Generator Governor Control 39
- 24 9440500990 Rev D 40
- 26 9440500990 Rev D 42
- Regulation DECS-250N 42
- Pre-Position Setpoints 43
- Transient Boost 44
- 9440500990 Rev D 29 45
- DECS-250N Regulation 45
- Reactive Droop Compensation 45
- Network Load Sharing 45
- 30 9440500990 Rev D 46
- Line Drop Compensation 46
- Autotracking 47
- Setpoint Configure 48
- Auxiliary Control 49
- Summing Type 50
- 9440500990 Rev D 35 51
- DECS-250N Auxiliary Control 51
- 36 9440500990 Rev D 52
- Auxiliary Control DECS-250N 52
- Contact Inputs and Outputs 53
- 9440500990 Rev D 39 55
- 40 9440500990 Rev D 56
- Protection 57
- 42 9440500990 Rev D 58
- Protection DECS-250N 58
- 9440500990 Rev D 43 59
- DECS-250N Protection 59
- Generator Undervoltage 59
- 44 9440500990 Rev D 60
- Generator Overvoltage 60
- Loss of Sensing 60
- Frequency Protection 61
- Power Protection 62
- 9440500990 Rev D 47 63
- Field Protection 64
- 9440500990 Rev D 49 65
- 50 9440500990 Rev D 66
- Exciter Diode Monitor 66
- 9440500990 Rev D 51 67
- 52 9440500990 Rev D 68
- Power Input Failure 68
- Sync-Check Protection 69
- Configurable Protection 70
- 9440500990 Rev D 55 71
- 56 9440500990 Rev D 72
- 58 9440500990 Rev D 74
- Limiters DECS-250N 74
- Takeover OEL 74
- 9440500990 Rev D 59 75
- DECS-250N Limiters 75
- 60 9440500990 Rev D 76
- Underexcitation Limiter 77
- 62 9440500990 Rev D 78
- Stator Current Limiter 79
- 64 9440500990 Rev D 80
- Low-Level Limiting 80
- High-Level Limiting 80
- Initial Delay 80
- Var Limiter 81
- Limiter Scaling 81
- Underfrequency Limiter 82
- GENERATOR VOLTS 83
- 68 9440500990 Rev D 84
- Metered Parameters 86
- 9440500990 Rev D 71 87
- DECS-250N Metering 87
- 72 9440500990 Rev D 88
- Metering DECS-250N 88
- 9440500990 Rev D 73 89
- Synchronization 89
- Auxiliary Control Input 89
- Tracking 89
- 74 9440500990 Rev D 90
- Control Panel 90
- 9440500990 Rev D 75 91
- Metering Summary 91
- Status Indication 92
- 9440500990 Rev D 77 93
- 78 9440500990 Rev D 94
- Outputs 94
- 9440500990 Rev D 79 95
- Network Load Share 95
- 80 9440500990 Rev D 96
- 9440500990 Rev D 81 97
- 82 9440500990 Rev D 98
- 9440500990 Rev D 83 99
- Real-Time Clock 99
- Auto Export Metering 100
- Event Recorder 101
- 86 9440500990 Rev D 102
- Event Recorder DECS-250N 102
- Triggers 102
- 9440500990 Rev D 87 103
- DECS-250N Event Recorder 103
- 88 9440500990 Rev D 104
- Trending 105
- 90 9440500990 Rev D 106
- Power System Stabilizer 107
- 92 9440500990 Rev D 108
- PSS Frequency Input Signal 109
- PSS Power Input Signal 110
- P0026-21 111
- 12-09-04 111
- 96 9440500990 Rev D 112
- Output Stage 112
- Terminal Voltage Limiter 112
- 9440500990 Rev D 97 113
- 98 9440500990 Rev D 114
- 9440500990 Rev D 99 115
- 100 9440500990 Rev D 116
- Stability Tuning 117
- Caution 118
- 9440500990 Rev D 103 119
- DECS-250N Stability Tuning 119
- Auto Tuning 119
- FCR and FVR Modes 120
- 9440500990 Rev D 105 121
- FVR Mode Stability Settings 121
- Other Modes and Functions 122
- 9440500990 Rev D 107 123
- 108 9440500990 Rev D 124
- Stability Tuning DECS-250N 124
- Mounting 125
- 110 9440500990 Rev D 126
- Mounting DECS-250N 126
- 9440500990 Rev D 111 127
- DECS-250N Mounting 127
- 112 9440500990 Rev D 128
- 9440500990 Rev D 113 129
- 114 9440500990 Rev D 130
- Terminals and Connectors 131
- 116 9440500990 Rev D 132
- 9440500990 Rev D 117 133
- 118 9440500990 Rev D 134
- Terminal Types 135
- 120 9440500990 Rev D 136
- Typical Connections 137
- 122 9440500990 Rev D 138
- 9440500990 Rev D 123 139
- 124 9440500990 Rev D 140
- BESTCOMSPlus 141
- Software 141
- Installation 142
- 128 9440500990 Rev D 144
- Software DECS-250N 144
- 9440500990 Rev D 129 145
- DECS-250N BESTCOMSPlus 145
- Menu Bars 146
- 9440500990 Rev D 131 147
- Settings Explorer 148
- Metering Explorer 148
- Settings File Management 149
- 134 9440500990 Rev D 150
- Automatic Metering Export 151
- Firmware Updates 151
- 9440500990 Rev D 137 153
- Updates 154
- BESTlogic™Plus 155
- 140 9440500990 Rev D 156
- BESTlogic™Plus DECS-250N 156
- BESTlogic™Plus Composition 156
- 9440500990 Rev D 141 157
- DECS-250N BESTlogic™Plus 157
- 142 9440500990 Rev D 158
- 9440500990 Rev D 143 159
- 144 9440500990 Rev D 160
- 9440500990 Rev D 145 161
- 146 9440500990 Rev D 162
- 9440500990 Rev D 147 163
- 148 9440500990 Rev D 164
- 9440500990 Rev D 149 165
- 150 9440500990 Rev D 166
- 9440500990 Rev D 151 167
- 152 9440500990 Rev D 168
- 9440500990 Rev D 153 169
- Logic Schemes 170
- 156 9440500990 Rev D 172
- 9440500990 Rev D 157 173
- Programming BESTlogic™Plus 174
- 9440500990 Rev D 159 175
- Pickup and Dropout Timers 175
- Offline Logic Simulator 176
- BESTlogic™Plus Examples 178
- Communication 179
- Modbus™ Communication 180
- 9440500990 Rev D 165 181
- DECS-250N Communication 181
- Ethernet Port 181
- CAN Communication 182
- Ethernet Communication 183
- 168 9440500990 Rev D 184
- Communication DECS-250N 184
- 9440500990 Rev D 169 185
- PROFIBUS Communication 186
- Configuration 187
- 172 9440500990 Rev D 188
- Configuration DECS-250N 188
- Generator PT 188
- Generator CTs 188
- 9440500990 Rev D 173 189
- DECS-250N Configuration 189
- Operating Power Input 189
- Modes of Operation 189
- Startup Functions 190
- Device Information 191
- Display Units 192
- 9440500990 Rev D 177 193
- 178 9440500990 Rev D 194
- Security 195
- Port Security 196
- Login and Access Controls 197
- 182 9440500990 Rev D 198
- Security DECS-250N 198
- Login Failure 198
- Timekeeping 199
- 184 9440500990 Rev D 200
- Timekeeping DECS-250N 200
- 9440500990 Rev D 185 201
- DECS-250N Timekeeping 201
- 186 9440500990 Rev D 202
- Testing 203
- Frequency Response 204
- 9440500990 Rev D 189 205
- DECS-250N Testing 205
- Bode Plotting 205
- Transfer Function 205
- Time Response 206
- 9440500990 Rev D 191 207
- Signal Input 207
- Test Signal Characteristics 207
- Step Response Analysis 208
- Analysis Options 209
- 194 9440500990 Rev D 210
- Testing DECS-250N 210
- CAN Parameters 211
- 196 9440500990 Rev D 212
- CAN Communication DECS-250N 212
- 9440500990 Rev D 197 213
- DECS-250N CAN Communication 213
- 198 9440500990 Rev D 214
- Modbus Modes of Operation 216
- 9440500990 Rev D 201 217
- Modbus on TCP/IP 217
- 202 9440500990 Rev D 218
- 9440500990 Rev D 203 219
- Read Holding Registers 219
- Return Query Data 219
- 204 9440500990 Rev D 220
- Listen Only Mode 220
- Preset Multiple Registers 220
- 9440500990 Rev D 205 221
- Preset Single Register 221
- Data Formats 222
- Modbus Parameters 224
- 9440500990 Rev D 209 225
- Binary Points 225
- 210 9440500990 Rev D 226
- 9440500990 Rev D 211 227
- 212 9440500990 Rev D 228
- 9440500990 Rev D 213 229
- 214 9440500990 Rev D 230
- 9440500990 Rev D 215 231
- 216 9440500990 Rev D 232
- 9440500990 Rev D 217 233
- 218 9440500990 Rev D 234
- Metering 234
- 9440500990 Rev D 219 235
- 220 9440500990 Rev D 236
- 9440500990 Rev D 221 237
- 222 9440500990 Rev D 238
- 9440500990 Rev D 223 239
- Limiters 239
- 224 9440500990 Rev D 240
- 9440500990 Rev D 225 241
- Setpoints 241
- 226 9440500990 Rev D 242
- 9440500990 Rev D 227 243
- Global Settings 243
- 228 9440500990 Rev D 244
- Relay Settings 244
- 9440500990 Rev D 229 245
- 230 9440500990 Rev D 246
- Protection Settings 246
- 9440500990 Rev D 231 247
- 232 9440500990 Rev D 248
- Gains Settings 248
- 9440500990 Rev D 233 249
- Legacy Modbus 249
- 234 9440500990 Rev D 250
- 9440500990 Rev D 235 251
- 236 9440500990 Rev D 252
- 9440500990 Rev D 237 253
- 238 9440500990 Rev D 254
- 9440500990 Rev D 239 255
- 240 9440500990 Rev D 256
- 9440500990 Rev D 241 257
- 242 9440500990 Rev D 258
- 244 9440500990 Rev D 260
- 9440500990 Rev D 245 261
- PROFIBUS Parameters 262
- 9440500990 Rev D 247 263
- 248 9440500990 Rev D 264
- 9440500990 Rev D 249 265
- 250 9440500990 Rev D 266
- 9440500990 Rev D 251 267
- 252 9440500990 Rev D 268
- 9440500990 Rev D 253 269
- 254 9440500990 Rev D 270
- 9440500990 Rev D 255 271
- 256 9440500990 Rev D 272
- 9440500990 Rev D 257 273
- 258 9440500990 Rev D 274
- 9440500990 Rev D 259 275
- 260 9440500990 Rev D 276
- 9440500990 Rev D 261 277
- 262 9440500990 Rev D 278
- 9440500990 Rev D 263 279
- 264 9440500990 Rev D 280
- 9440500990 Rev D 265 281
- 266 9440500990 Rev D 282
- 9440500990 Rev D 267 283
- 268 9440500990 Rev D 284
- 9440500990 Rev D 269 285
- 270 9440500990 Rev D 286
- 9440500990 Rev D 271 287
- 272 9440500990 Rev D 288
- 9440500990 Rev D 273 289
- 274 9440500990 Rev D 290
- 9440500990 Rev D 275 291
- 276 9440500990 Rev D 292
- 9440500990 Rev D 277 293
- 278 9440500990 Rev D 294
- 9440500990 Rev D 279 295
- 280 9440500990 Rev D 296
- 9440500990 Rev D 281 297
- 282 9440500990 Rev D 298
- 9440500990 Rev D 283 299
- 284 9440500990 Rev D 300
- 9440500990 Rev D 285 301
- 286 9440500990 Rev D 302
- 9440500990 Rev D 287 303
- 288 9440500990 Rev D 304
- 9440500990 Rev D 289 305
- 290 9440500990 Rev D 306
- 9440500990 Rev D 291 307
- 292 9440500990 Rev D 308
- 9440500990 Rev D 293 309
- 294 9440500990 Rev D 310
- 9440500990 Rev D 295 311
- 296 9440500990 Rev D 312
- 9440500990 Rev D 297 313
- 298 9440500990 Rev D 314
- 9440500990 Rev D 299 315
- 300 9440500990 Rev D 316
- 9440500990 Rev D 301 317
- 302 9440500990 Rev D 318
- Maintenance 319
- Troubleshooting 320
- Support 321
- 306 9440500990 Rev D 322
- Maintenance DECS-250N 322
- Specifications 323
- Generator Current Sensing 324
- Accessory Inputs 325
- Contact Inputs 325
- Communication Ports 325
- Contact Outputs 326
- Field Power Output 327
- Regulation 327
- Parallel Compensation 328
- Field Protection Functions 329
- Startup 330
- Voltage Matching 331
- Data Logging (Oscillography) 332
- Environment 332
- Type Tests 332
- Physical 333
- Regulatory Standards 333
- 318 9440500990 Rev D 334
- Specifications DECS-250N 334
- Analog Expansion Module 335
- 322 9440500990 Rev D 338
- Connections 338
- 324 9440500990 Rev D 340
- AEM-2020 341
- 9440500990 Rev D 327 343
- Communications 344
- Functional Description 344
- 9440500990 Rev D 329 345
- RTD Inputs 345
- 330 9440500990 Rev D 346
- Thermocouple Inputs 346
- 9440500990 Rev D 331 347
- Analog Outputs 347
- 9440500990 Rev D 333 349
- Analog Input Values 349
- 334 9440500990 Rev D 350
- 336 9440500990 Rev D 352
- Contact Expansion Module 353
- 340 9440500990 Rev D 356
- 9440500990 Rev D 341 357
- 9440500990 Rev D 343 359
- 344 9440500990 Rev D 360
- 9440500990 Rev D 345 361
- 9440500990 Rev D 347 363
- Revision History 365
Related products and manuals for Accessories for electrical Basler-electric DECS-250N
(250 pages)
(698 pages)
(718 pages)
(716 pages)
(704 pages)© 2020, manymanuals.com. All rights reserved. | 0.108 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals